At a Glance: Matched bearing, gear and rotor kit for the TC20180 RS25 20V brushless reciprocating saw
When the heart of your Tork Craft RS25 reciprocating saw starts to complain – extra vibration, noise or a loss of power – it is time
to look at the rotating parts. The TC20180-SK02 Bearing & Gear & Rotor Kit brings the key internal components together in one genuine
spare set so you can restore smooth running, efficiency and cutting performance instead of retiring a good 20V brushless saw.
Complete rotating assembly spare kit for the TC20180 RS25 saw
This Tork Craft kit covers a group of parts identified as items 10, 12, 16–19, 35, 49–51, 53–55 and 57 on the TC20180 exploded diagram.
It typically includes the rotor, key gears and the supporting bearings that carry the load at 2 800 strokes per minute.
Replacing these components together helps ensure correct fit and alignment, giving your RS25 reciprocating saw a fresh lease of life
for demanding cutting work in wood, metals and demolition materials.
Extra Information
Specifically intended for the Tork Craft TC20180 RS25 20V brushless reciprocating saw – check the model number on your tool before ordering.
Refer to the official TC20180 parts list or exploded diagram to see the exact position of items 10, 12, 16–19, 35, 49–51, 53–55 and 57 inside the tool.
Best fitted when there are signs of bearing noise, visible rotor damage, excessive play or when the saw has suffered a major overload.
Installation is recommended for experienced users or service technicians familiar with strip-down and re-assembly of cordless power tools.
Record approximate pack dimensions and weight separately in your admin console for shipping and handling fields.
Pro Tip
Before you remove the old rotor and gears, mark the original orientation of components and take step-by-step photos.
This makes it much easier to seat the new parts correctly, especially where shims, spacers or thrust washers are involved.
Features
Genuine Tork Craft spare kit – Factory-specified bearing, gear and rotor components for the TC20180 RS25 saw.
Covers multiple internal parts – Includes the main rotor, drive gear and associated bearings as per items 10/12/16–19/35/49–51/53–55/57.
Designed for 20V brushless RS25 – Matches the original brushless drive system and housing tolerances.
Pre-matched components – Parts are selected to work together as a set for correct meshing and support.
Supplied as a service kit – Ideal for a complete overhaul when the original rotating group is worn or damaged.
Benefits
Restore cutting performance: Fresh bearings, gears and rotor help the saw run smoother with more consistent power.
Reduce vibration and noise: Replacing worn rotating parts can noticeably improve comfort and control in use.
Extend tool life: Protects your investment in the RS25 by renewing the high-stress internal components.
Save time on part selection: A single kit avoids the guesswork of ordering individual bearings and gears.
Support safe operation: Properly supported and aligned moving parts reduce the risk of unexpected failure under load.
Safety
Remove the 20V battery pack from the saw before opening the housing or working on any internal components.
Work on a clean, stable surface and keep small parts, bearings and fasteners organised to avoid losing anything critical.
After fitting the kit, turn the mechanism by hand first to check for smooth operation before refitting the battery.
Run the saw at no-load for a short period to bed in the new components and listen for any unusual noise.
If you are not confident performing the repair, contact an authorised Tork Craft service centre or a qualified technician.
Specifications
Description
Spec
Brand
Tork Craft
Cat No.
TC20180-SK02
Product Type
Bearing & Gear & Rotor Service Kit
Compatible Tool Model
TC20180 RS25 20V Brushless Reciprocating Saw
Key Components
Rotor, drive gear and associated bearings (items 10/12/16–19/35/49–51/53–55/57)
Typical Application
Replacement of worn, noisy or damaged rotating assembly components